分分pk10

停车场环氧地坪漆的中涂层施工技巧,徐州塑胶地坪

欢迎来到徐州军盛地坪工程有限公司
全国咨询热线

18052255733

联系方式

    军 盛 地 坪

     

    联系电话:0516-88328212

    手机:18052255733

    企业邮箱:AXAfloor@163.com

    公司地址:徐州红叶南路大观园旭旺超市北50米


停车场环氧地坪漆的中涂层施工技巧

发布时间 : 2018-11-27 10:35:40      访问量 : 319次

1、工前需确保地面干净,如有杂物粘附需清除;2、将环氧树脂和固化剂按正确比例混合搅拌,并按配比加上一定的石英砂;3、搅拌均匀后倾倒在地面上,使用镘刀按设计的厚度将材料均匀镘开,以增加强度和耐冲击力;使地面更加结实,抗压。4、停车场施工中涂层干固后,采用打磨,把表面的流挂物、颗粒打磨平整。5、灰尘处理干净。

http://www.jsdpxz.com/


1. Make sure that the ground is clean before the parking lot epoxy floor painter, if there is any debris adhesion, it needs to be removed; 2. Mix epoxy resin and curing agent in the right proportion and add certain quartz sand according to the proportion; 3. Pour the material on the ground after mixing evenly, and use the trowel knife to evenly open the material according to the designed thickness, so as to increase the strength. And impact resistance; make the ground more solid and compressive. 4. After the coatings of epoxy floor paint in parking lot are dried and solidified, the surface hangings and particles are polished and smoothed. 5, dust disposal is clean.

检验方法:施工交接处理是否妥当,踢脚线位置平直,与墙壁无离间,平整。

Inspection method: Whether the construction handover treatment is appropriate, the position of kick line is straight, no separation from the wall, flat.

环氧腻子层

Epoxy putty layer

1、在停车场环氧地坪漆施工洁净后的地面上,将环氧树脂和石英粉按正确的配比搅拌均匀后,采用批刀均匀镘刮在地面上,以增加中涂与面层之间的结合,并进一步调整地面的平整度;2、视实际需要施工遍数,要求达到平整无孔洞,无批刀印及砂磨印为准。

1. After mixing epoxy resin and quartz powder in the right proportion on the clean ground after parking lot floor paint construction, the batch knife is used to scrape evenly on the ground to increase the combination between the middle coating and the surface layer, and further adjust the smoothness of the ground; 2. According to the actual needs of construction times, it is required to achieve a level without holes. No batches of knife and sand print are allowed.

检验方法:使地面完全平整无孔洞,无批刀印及砂磨印方可进行面涂层施工。

Inspection method: To make the ground completely flat without holes, no batch of knife prints and sanding prints before surface coating construction can be carried out。 


咨询热线:
18052255733
在线客服:
客服
官方微信站:

在线留言 当前未读信息 159 条!

北京赛车pk拾冠军玩法 甘肃快3 甘肃快3 甘肃快3 北京赛车pk10中奖规则 甘肃快3 欢乐棋牌 北京赛车pk10综合走势图 欢乐棋牌 欢乐棋牌官网